New generation monitoring CPE

• IP65/Available
  

• Easy to install /Convenient
  

• Easy to set/Easy to handle
  

• POE power Supply/Flexible
  

• Low-power/Eergy Saving
  

• SSID Hiding/High Security
  

• Qualcomm Chip/Excellent/performance

• Auto Channel/Selection

Stable Transmission high-defination quality

CPE work in the 2 .4GHz band, the transmission rate reach to 300Mbps, ensure monitor image quality is stable, clear, and not droppedEasy to install

No need install tools, supports pole mounted and wall mounted, convenient and flexibleSignal tracking & Precise positioning

The CPE comes with signal indicator, users can adjust the angel of the CPE according to the signal strength, easy to achieve high quality of long -range wireless transmission effectNot afraid of outdoor harsh environment

Profession outdoor engineering plastic shell, Strict silk Stitching. Dustproof, waterproof, adapt to bad weather such as wind, frost, rain and snow.Even in the extreme high-low temperature environment (-40>559C) can be also work as usual.Anti-interference Broadband

Support 2.3-2.7GHz broadband, support more channel optional,Significantly reduced co-channel signal interference,Data transfer is smooth and will not be lostQualcomm chipset, Quality Assurance

Adopt Qualcomm chipset 650MHz high frequency chipset,which improve the CPU performance and reduce power consumption. (Stability has been tested by engineering users)Powerful Hardware Configuration

Boot：low temperature working modulePOE power supply

9-24V 0.5A power supply,specification wiring reduce networking costHide SSID, Refuse other people to get free WiFi

Comfast wireless CPE support SSID Broadcast hide,can easy solve the troubles of network security and ensure the engineering stabilityDiverse software management functions

COMFAST wireless CPE software has a scientific and user-friendly operation interface. And the user is easy to set up, easy to use, rich in functions and practicalWireless Monitor Connected Diagram

Point to Point Connection Diagram

Multiple cameras connection way 1: Connection the cameras to the switch,then connect with the COMFAST CPE.It will transmit the data through two CPE

Set-up Mode: Terminal Mode：Camera > Switch > CPE

Set-up Mode: AP Mode：CPE> NVR > Monitoring ComputerMultiple cameras connection way 2: If the distance among the cameras is so far ,each camera is configured with two CPEs.The control center connect CPE with AP mode through the switch,then connect with the NVR Set-up Mode: Terminal Mode

Set-up Mode: Terminal Mode：Camera >  CPE

Set-up Mode: AP Mode：CPE> Switch>NVR >Monitoring ComputerPoint to Muti-point Connection Diagram

If the angle of camera and monitor center is less than 60degree,there can consider one point to multi point connection.It can reduce CPEs with the transmitting mode,which can save project cost a lot.Pls pay attention that it has to meet the angle and Broadband requirement

In wireless monitoring transmission,we suggest you to use above way to do connection.Pls pay attention the transmission angle for the device is 60 degree.

Camera >  CPE

CPE> NVR > Monitoring Computer

Dear customer, if you have any questions you can contact us at any time, please contact us before raising any disputes or leaving any neutral/negative feedback, we will try our best to solve it for you, your satisfaction is always our first priority.

Q1: How long Range is the wifi transmission distance of this device?

Q2: What is the frequency of this device? What is the transfer rate?

2.4Ghz, 300Mbps.

Q3: What scenario is this device used for?

It is suitable for security monitoring projects, monitoring project transmission in scenic spots, ports, oil fields, construction sites, etc.It also suitable for long range wifi transmission

Q4: Is it possible to receive internet from my home router via WiFi and transmit it further?

Yes, the WiFi bridge can be used as a transmitter or a receiver (for reference only, the specific application needs to be combined with the actual situation)

Q5: Can this device be installed with only one?

Yes, a device can be set to AP mode and repeater mode, but the transmission distance of WiFi is the same as the normal relay and AP coverage. If you use one device, it is recommended to set AP mode.

Q6: Failed to power on the outdoor Wi-Fi bridge?

Please connect the WAN port of the product to the port of the POE adapter.

If the connection is correct, but still cannot start, please try to replace the adapter and rj45 network cable.

CF-E314N V2

Suggestion

The distance "3-5KM" mean 2pcs CPE based on point to point bridge mode.

There are many factors that affect distance, such as obstacles

(trees, walls, buildings, trucks, etc.), raw network signals, etc

If you want the good signal, we suggest you buy 2pcs!